6mm Swift (Handloader issue 358) |
![]() |
| Warning! Notes: A benchrest rifle built during the 1940s by L.R. Wallack on an FN Mauser action was used to test all loads. The rifle was fitted with a Dayton-Traister trigger, a heavy 26-inch G.R. Douglas barrel with a 1:12-inch twist and a Unertl 2-inch 24x scope. Winchester .220 Swift cases necked up to 6mm and CCI 200 primers were used throughout. The powder charges shown appeared to be maximum, or close to maximum, and should be reduced by 10 percent when developing starting loads for other rifles. Accuracy figures represent the average of five five-shot groups. Velocities were measured using an Oehler Model 33 chronograph. |
|
Cartridge History
6mm Swift
The 6mm Swift is an American wildcat cartridge created by expanding the neck of the .220 Swift case to accept .243-inch bullets. Its development was connected to the growth of organized benchrest competition during the 1940s, when shooters and gunsmiths experimented with cartridges that could offer greater wind resistance than the fast .22-caliber rounds then in use. The precise origin of the cartridge is not completely documented, although Remington engineer and accomplished benchrest competitor Mike Walker is often associated with a version formed by necking the standard .220 Swift case up to 6mm without making other significant changes. The cartridge’s ancestry forms an interesting circle in American ammunition development. Winchester’s 6mm Lee Navy cartridge was adopted by the United States Navy in 1895 and was among the earliest American military cartridges designed for smokeless powder. Winchester later used the Lee Navy case as the basis for the .220 Swift, reducing its neck to accept .224-inch bullets and modifying the case for use in commercial sporting rifles. Introduced in 1935, the .220 Swift became famous for exceeding 4,000 feet per second. Early wildcatters subsequently expanded its neck back to 6mm, effectively returning the case to approximately its original bullet diameter while retaining the Swift’s stronger case construction and revised dimensions. During the early years of modern benchrest shooting, cartridges such as the .219 Donaldson Wasp, .220 Swift, .22-250 and .220 Wilson Arrow were successful at 100 and 200 yards. Their light bullets, however, could be affected substantially by wind at 300 yards. Larger cartridges such as the .270 Winchester and .30-06 Springfield offered heavier bullets but also produced more recoil, which made precise shooting more difficult. The 6mm bore represented a useful compromise by combining relatively light recoil with heavier bullets that resisted wind better than the small .22-caliber projectiles of the period. The growing availability of accurate .243-inch bullets helped make the concept practical. Fred Huntington, who founded Rock Chuck Bullet Swage—later known as RCBS—in 1943, produced match-grade 6mm bullets and equipment that allowed competitors to form their own bullets. A typical early 6mm Swift benchrest rifle used bullets weighing approximately 65 to 90 grains. Rifles were often constructed on strong actions such as the FN Mauser and fitted with heavy barrels and long, externally adjustable target scopes. A rifling twist near 1:12 was commonly selected because it provided suitable accuracy with the bullet lengths then favored by benchrest shooters. Forming the basic cartridge was comparatively simple because a tapered expander could open the neck of a .220 Swift case to 6mm. Some wildcatters retained the original case body and shoulder, while others reduced body taper or increased the shoulder angle to create improved variations. One example was Homer Brown’s .240 Cobra. Because wildcat chamber dimensions were not universally standardized, ammunition had to be formed specifically for the individual rifle. Dies, chamber measurements and fired cases were therefore essential when working with an older rifle of uncertain origin. The 6mm Swift had less powder capacity than later cartridges such as the .243 Winchester, .244 Remington and 6mm Creedmoor. A representative Winchester case held approximately 46.8 grains of water, compared with about 53.4 grains for the .243 Winchester. Although the smaller capacity limited maximum velocity, it was entirely adequate for the short-range benchrest competition of its era. The introduction of the commercial .243 Winchester and .244 Remington in 1955 reduced the practical need for many early 6mm wildcats, while the later 6mm PPC eventually became dominant in short-range benchrest shooting. The 6mm Swift never became a standardized factory cartridge, but it represents an important stage in the development of American 6mm target cartridges. It combined the strong and proven .220 Swift case with the emerging accuracy advantages of match-grade .243-inch bullets. Handloader Issue No. 358 examines the cartridge alongside other early 6mm developments and recounts its use in a vintage benchrest rifle dating from the 1940s. |
| Be Alert: Publisher cannot be responsible for errors in published load data. |
| Wt. | Bullet | Powder Manufacturer | Powder | Charge | Velocity (FPS) | |
| 60 | Watson FBHP | IMR | IMR-4064 | Subscribe | 3548 | |
| Remarks: COAL (inches): 2.690; 100-yard group (inches): .445 | ||||||
| 65 | Shilen FBHP | IMR | IMR-4064 | Subscribe | 3510 | |
| Remarks: COAL (inches): 2.775; 100-yard group (inches): .510 | ||||||
| 68 | Berger FBHP | IMR | IMR-4064 | Subscribe | 3489 | |
| Remarks: COAL (inches): 2.720; 100-yard group (inches): .487 | ||||||




